everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 1 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng technical data sheet 0603 package chip led (0.6mm height) 19 - 213/ gh c - yp1q2qy /3t features ? package in 8mm tape on 7 diameter reel. ? compatible with automatic placement equipment. ? compatible with infrared and vapor phase reflow solder process. ? mono - color type. ? pb - free . ? the product itself will remain within rohs complaint version descriptions ? the 19 - 21 3 smd led is much smaller than lead frame type components, thus enable small er board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ? besides, lightweight makes them ideal for miniature applications. etc. applications ? b acklighting in dashboard and switch. ? telecommunication: in dicator and backlighting in telephone and fax. ? flat backlight for lcd, switch and symbol. ? general use. device selection guide part no. chip emitted color resin color material 19 - 213/ ghc - yp1q2qy/3t in gan brilliant green water clear
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 2 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng package outli ne dimensions note: the tolerances unless mentioned are 0.1mm, u nit = mm .
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 3 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng absolute maximum ratings (ta=25 parameter symbol rating unit reverse voltage v r 5 v forward current i f 25 ma peak forward current (duty 1/10 @1khz) i f p 100 ma po wer dissipation pd 95 mw electrostatic discharge (hbm) esd 150 v operating temperature topr - 40 ~ +85 storage temperature tstg - 40 ~ +90 soldering temperature tsol reflow soldering:260 for 10 sec hand soldering:350 for 3 sec electro - optical cha racteristics (ta=25 parameter symbol min. typ. max. unit condition luminous intensity iv 45.0 ---- 112 mcd i f = 5 ma viewing angle 2 1/2 ---- 120 ---- deg peak wavelength p ---- 518 ---- nm dominant wavelength d 520 ---- 535 nm spectrum radiation bandwidth ---- 35 ---- nm forward voltage v f 2.70 ---- 3.20 v reverse current i r ---- ---- 50 a v r = 5v notes: 1.tolerance of luminous intensity 2 .tolerance of dominant wavelength 3.tolerance of forward voltage
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 4 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng b in rang e of dom. wavelength group bin min max unit condition y x 520 525 nm i f = 5 ma y 525 530 z 530 535 bin rang e of luminous intensity bin min max unit condition p1 45.0 57.0 mcd i f = 5 ma p2 57.0 72.0 q1 72.0 90.0 q2 90.0 112 bin rang e of forward voltage group bin min max unit condition q 29 2.70 2.80 v i f = 5 ma 30 2.80 2.90 31 2.90 3.00 32 3.00 3.10 33 3.10 3.20 notes: 1.tolerance of luminous intensity 2 .tolerance of dominant wavelength 3.tolerance of forward voltage
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 5 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng typical electro - optical characteristics curves relative luminous intensity ambient temperature t (c ) a % ) ( relative luminous intensity ( ) % wavelength (nm) ta=25c forward voltage v (v) f forward current i (ma) relative luminous intensity ( ) % forward current i (ma) ta=25c ambient temperature t (c a ) forward current i (ma) ta=25c 0.7 0.9 0.8 1.0 0.4 0.3 0.5 0.1 0.2 70 0.6 80 90 50 60 40 radiation diagram 0 10 20 30 ta=25c
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 6 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng label explanation cat: luminous intensity rank hue: dom. wavelength rank ref: forward voltage rank reel dimensions n ote: the tolerances unless mentioned are 0.1mm, u nit = mm . rohs pb cpn : p n : xxxxxxxxxxxxx xxxxxxxxxxxxx qty : xxx lot no : xxxxxxxxxx reference : xxxxxxxx cat : xxx hue : xxx ref : xxx everlight made in taiwan
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 7 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng carrier tape dimensions: loaded quantity 3 000 pcs per reel note: the tolerances unless mentioned are 0.1mm, u nit = mm moisture resistant p ackaging label aluminum moisture-proof bag desiccant label
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 8 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng reliability test items and conditions the reliability of products shall be satisfied with items listed below. confidence level 90% ltpd 1 0% no. items test condition test hours/cycles sample size ac/r e 1 reflow soldering temp. : 2 6 0 22 p cs. 0/1 2 temperature cycle h : + 100 22 pcs. 0/1 3 thermal shock h : +100 22 p cs. 0/1 4 high temperature storage temp. : 100 22 p cs. 0/1 5 low temperature storage temp. : - 40 22 p cs. 0/1 6 dc operating life i f = 20 ma 1000 hrs. 22 p cs. 0/1 7 high temperature / high humidity 85 22 p cs. 0/1
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 9 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng precautions for use 1. over - current - proof customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( burn out will happen ). 2. storage 2.1 do not open moisture proof bag before the products are ready to use. 2.2 before openin g the package, the leds should be kept at 30 or l ess and 90%rh or less. 2.3 after opening the package : t he led's floor life is 1 year under 30 or less and 6 0% rh or less. if unused leds remain, it should be stored in moisture proof packages. 2. 4 if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : 60 5 for 24 hours. 3. soldering condition 3.1 pb - free solder tempe rature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board.
19 - 213/ gh c - yp1q2qy /3t everlight electronics co., ltd. http://www.everlight.com rev. 1 page: 10 of 10 device no: prepared date: 1 - jul - 20 11 prepared by: chen zheng 4.soldering iron each terminal is t o go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the damage of the product is of ten started at the time of the hand solder. 5.repairing repair should not be done after the leds have been soldered. when repairing is unavoidable, a double - head soldering iron should be used (as below figure). it should be confirmed beforehand whe ther the characteristics of the leds will or will not be damaged by repairing. everlight electronics co., ltd. tel: 886 - 2 - 2267 - 2000, 2267 - 9936 office: no 25, lane 76, sec 3, chung yang rd, fax: 886 - 2267 - 6244, 2267 - 6189, 2267 - 6306 tucheng, taipei 236, taiwan, r.o.c http://www.everlight.com
|
